-
PROCLIP CENTER MOUNT, Extra strength mounting platform. - Dodge / Ram Trucks 2009 - 2018
-
RAM Center Dash Mount - Extra-Strength with Mount - NOT for Classic models or models with the large 12 inch display screen. For the Classic models, see our 2018 listings. - - This item does not come with fasteners for attaching a device holder.
-
PROCLIP CENTER MOUNT, Extra strength mounting platform. - Dodge / Ram Trucks 2019 - 20xx
-
PROCLIP CENTER MOUNT EXTRA STRENGTH hev Silverado and GMC Sierra 1500 2019 - 20xx Chevrolet Silverado and GMC Sierra 2500-3500 2020 - 20xx
-
Angled Dash Mount for Freightliner Cascadia 2018-2020. Clips into the seams of the dashboard. Easily attach a device holder to the mount. Secure fit within easy reach from the driver's seat. No holes or damage to your dashboard. Strong enough to hold a device in a Tough Sleeve. The mount will come with 2mm pre-drilled holes
-
PROCLIP CENTER MOUNT EXTRA STRENGTH - Ford Transit 2020 - 20xx Ford Tourneo Custom 2019 - 20xx
-
Standard Left/Right Extension Plate. 100 x 50 x 5 mm (3.94 x 1.97 x 0.20 in). Avoid interference with the dashboard controls/displays when using wide devices. To extend your device to the left or right from the Vehicle Mount (especially the ProClip Angled Mount) to avoid interference with the dashboard controls/displays. Extension plates may not line up with the pre-drilled holes on your ProClip mount. The included self-tapping screws can be used to screw anywhere into the mount face.
-
This Tilt-Swivel is made for use with holders for heavier devices e.g. Tablets, Mobile Computing devices, Bar Code Scanners, Two-way Radios etc. Tilt, swivel and/or extend your holder/device for a better viewing position. It tilts approx. 15 degrees, swivels 360 degrees and extends 1 inch/ 2.54 cm. The Base plate has AMPS hole pattern and the face plate has several hole patterns including AMPS to accommodate most holders, cradles, mounts and car kits.
-
Perfect for installing any equipment that needs to be turned for use from different directions to be seen by multiple users. Swivels 340 degrees. AMPS hole pattern to attach any ProClip device holder onto.
-
This Pedestal Mount Round Mounting Plate creates an extra sturdy and secure mounting platform that can be used in aircrafts, boats and a variety of vehicles e.g. personal vehicles, commercial vehicles, emergency vehicles, police vehicles, trucks, tractors, fork lifts and RVs. Additionally, the Pedestal Mount Extension Rod can be used with mounts in retail stores, kiosks, gyms, conference rooms, trade shows etc.
-
PEDESTAL MOUNT KIT 6 INCH WITH SWIVEL HEAD (Pre-assebled with 4 inch Circular Plate, 6 Inch Pedestal Mount, Swivel Head, Locking Move Clip Heavy Duty Female Plate)
-
This 4 inch aluminum Mount has teeth within the interlocking joints providing a very strong connection. It can be used in a variety of vehicles or fixed locations to mount a wide variety of products such as tablets and mobile computers. - These come in 2, 4, 6, 8 and 10 heights with and AMPS base and top and can be purchased in complete sets or as individual pieces. - The design allows you to mix and match the parts to create your own unique design/solution.
-
This 6 inch aluminum Mount has teeth within the interlocking joints providing a very strong connection. It can be used in a variety of vehicles or fixed locations to mount a wide variety of products such as tablets and mobile computers. - These come in 2, 4, 6, 8 and 10 heights with and AMPS base and top and can be purchased in complete sets or as individual pieces. - The design allows you to mix and match the parts to create your own unique design/solution.
-
If you need to attach a device holder or a angled top plate to one of our pedestals this set of screws is a perfect fit. Includes four screws and locking nuts for a secure hold. Extra screw set for aluminum pedestal mounts. Fits round plastic base with threaded inserts. Includes: 4 screws / 4 lock nuts
-
This 4 inch Pedestal Mount Kit creates an extra sturdy and secure mounting platform that can be used in a variety of vehicles and fixed locations like retail stores, kiosks, gyms, conference rooms, trade shows etc. The Pedestal Mount Kit come in 4 inches high with 100mm round base and AMPS top. The design allows you to mix and match the parts, or combine complete sets with loose parts to create your own unique design/solution. The base and the rods can be angled in steps of 24 degrees.
-
45 degree Angled Top part to mount a device holder onto. Fits all ProClip pedestals. The top has four holes for mounting onto the top part of a Pedestal Mount. It has dual AMPS-holes for mounting of holder for unit.
-
Angled Top Part - 60 Degrees Angles the top part of the Pedestal Fits both Solid Core and Hollow Core Pedestals Dual AMPS-hole patterns for mounting of a device holder
-
This 6.5 inch Pedestal Mount is very strong yet light weight. It is designed for a discreet cable entry, where the cable is passed through the Pedestal Mount. The pedestal top swivels 340 degrees. You can easily combined the Pedestal Mount with an angled top part. It has a 6 hole base for attaching to any flat surface or one of our Round Mounting Plates for additional strength.
-
M4 x 12mm Hex Cap Screws with Nyloc Nuts (4 pk), Blk. These black cap screws and lock nuts are an effective way to attach any ProClip device holder directly to the base plate of any one of our Standard Duty or Heavy Duty Mounts.
-
MultiStand for Apple iPad Mini with Retina display. This Holder is made to fit the tablet without a case. Easily snap your device in and out of the holder. Provides for safer driving when viewing, accessing and operating your device in the vehicle. Custom fit to your bare device. Includes Tilt-Swivel to angle holder 15 degrees any direction. Rotate between portrait and landscape view. Combine with a ProClip vehicle mount to make a full mounting solution
-
The VESA ProClip adapter plate attaches to any existing 75mm and 100mm VESA mounting system to create a new flat mounting surface to allow the attachment of ProClip specific mounts and other mounts/devices.
-
For installation of devices on pipes and stays, for example most types of vehicles; motorcycles, boats, carts, stands, wheelchairs, airplanes etc. The mount has a mounting plate sized 50x42 mm with pre-drilled AMPS-holes. The mount fits pipes with diameter 19 mm or 3/4 inch is the smallest diameter pipe or bar. 30 mm or 1 1/8 inch is the largest diameter pipe or bar. Made in black plastic.
-
For installation of devices on pipes and stays, for example most types of vehicles; motorcycles, boats, carts, stands, wheelchairs, airplanes etc. The mount has a mounting plate sized 160x50 mm with 6 pre-drilled holes. The mount fits pipes with diameter 19 mm or 3/4 inch is the smallest diameter pipe or bar. 30 mm or 1 1/8 inch is the largest diameter pipe or bar. Made in black plastic.
-
For installation of devices on pipes and stays, for example most types of vehicles; motorcycles, boats, carts, stands, wheelchairs, airplanes etc. The mount has a 45 degree mounting plate sized 160x50 mm with 6 pre-drilled holes. The mount fits pipes with diameter 19 mm or 3/4 inch is the smallest diameter pipe or bar. 30 mm or 1 1/8 inch is the largest diameter pipe or bar. Made in black plastic.
-
For installation of devices on pipes and stays, for example most types of vehicles; motorcycles, boats, carts, stands, wheelchairs, airplanes etc. The mount has a 90 degree mounting plate sized 160x50 mm with 6 pre-drilled holes. The mount fits pipes with diameter 19 mm or 3/4 inch is the smallest diameter pipe or bar. 30 mm or 1 1/8 inch is the largest diameter pipe or bar. Made in black plastic.
-
Wing nut kit for use with ProClip aluminum mounts. Allows easy adjustment and removal of mount parts. - Fits all extension rod sizes - Metal spacer for use with ProClip mounts - 2 Wing Nuts / 2 Metal Spacers / 2 Bolts
-
Perfect for use with all types of forklifts. Attach a custom ProClip device holder directly to the face plate or add a ProClip Mount for even more flexibility. - Works perfectly on the roll bar of a forklift - The forklift mount can be mounted on square surfaces - Multiple sets of AMPS holes makes the fitting of a ProClip mount base easy - Comes with complete set of screws in various sizes, allowing for the forklift mount to span from 130mm to 5mm
-
The ProClip Quick Release Dock works with any ProClip device holder with a Tilt-Swivel. Easily remove a holder from its mounting location without the use of tools. - 15 mm Extended release tab for easy device removal - Allows you to switch device holders without changing the mount - Fits all ProClip Device Holders with Tilt-Swivel or male adapter block
